View ZHX1203_1339067.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ZHX1203
SIR UltraSlimTM Transceiver (IrMC)
Preliminary Product Specification
PS016402-1102
ZiLOG Worldwide Headquarters * 532 Race Street * San Jose, CA 95126-3432 Telephone: 408.558.8500 * Fax: 408.558.8300 * www.ZiLOG.com
This publication is subject to replacement by a later edition. To determine whether a later edition exists, or to request copies of publications, contact: ZiLOG Worldwide Headquarters
532 Race Street San Jose, CA 95126-3432 Telephone: 408.558.8500 Fax: 408.558.8300 www.ZiLOG.com
ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other products and/or service names mentioned herein may be trademarks of the companies with which they are associated.
Document Disclaimer
(c)2002 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZiLOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. Devices sold by ZiLOG, Inc. are covered by warranty and limitation of liability provisions appearing in the ZiLOG, Inc. Terms and Conditions of Sale. ZiLOG, Inc. makes no warranty of merchantability or fitness for any purpose. Except with the express written approval of ZiLOG, use of information, devices, or technology as critical components of life support systems is not authorized. No licenses are conveyed, implicitly or otherwise, by this document under any intellectual property rights.
P
R
E
L
I
M
I
N
A
R
Y
PS016402-1102
ZHX1203 SIR UltraSlim Transceiver (IrMC)
iii
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC Positive Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SD Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RxD Receive Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TxD Transmit Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDA LED Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB Shield Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 3 3 3 3 3 3
Application Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical and Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ZHX1203 Tape and Reel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ZHX1203 Soldering and Cleaning Recommendations . . . . . . . . . . . . . . . . . . . . Reflow Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 9 9 9
Moisture Prevention Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Baking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mechanical Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Customer Feedback Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Return Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Problem Description or Suggestion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 12 12 12 12
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
iv
List of Figures
Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. UltraSlim Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ZHX1203 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ZHX1203 Application Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . 4 ZHX1203 Reel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ZHX1203 Tape Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Temperature Profile for the Top Surface . . . . . . . . . . . . . . . . . . . . . . 9 ZHX1203 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 ZHX1203 Mechanical Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
List of Tables
Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. ZHX1203 Transceiver Pin Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . Receiver Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . Transmitter Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . Transceiver Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 2 5 5 5 6 7
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
1
Description
The ZILOG ZHX1203 for mobile phones, pagers, and PDAs is the smallest, lowest power, and highest functional transceiver in its class. Communication takes place at the low receive current consumption of 100 A (typical). The ZHX1203MB features only the low receive current consumption of 100 A (typical). The UltraSlim form factor (7.3 mm long x 2.8 mm wide x 1.9 mm high) allows placement in virtually any small device (see Figure 1). Application circuit space is also minimized because only two external components are required.
Figure 1. UltraSlim Form
The ZHX1203 is designed to support IrDA-Data SIR mode, which at 115 Kbits/s provides the capability for the user to share phone numbers, addresses, and notes as well as linking a PC to the internet via a mobile telephone. The transceiver combines an IRED emitter, a photodiode, and a unique driver/ control ASIC in a single package, as shown in Figure 2. The ZILOG ZHX1203 also features a shutdown control that minimizes current draw to 0.1 A typical.
Figure 2. ZHX1203 Block Diagram
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
2
Features * * * * * * * *
Compliant to IrDA Data Specification 1.4 Low Power SIR (link range: low power to low power--0 to 20 cm; standard power to low power--0 to 30 cm) Low-power supply voltage range: 2.4 V to 3.6 V ZHX1203MB receive current: 100 A (typical) UltraSlim package: 7.3 mm long x 2.8 mm wide x 1.9 mm high Only two external components Extended operating temperature range: -30 C to +85 C Internal current source eliminates need for a current-limiting resistor for IR LED Meets IEC 825-1 Class 1 eye safety specifications
Pin Description
Table 1 lists the pin out for the ZHX1203 transceiver. The pins are described in this section.
Table 1. ZHX1203 Transceiver Pin Out Pin 1 2 3 4 5 6 7 -- Name NC VCC GND SD RxD TxD LEDA TAB Function NC (future use) Supply voltage Ground Shutdown Receiver output Transmitter input IRED anode Shield connection I/O -- -- -- I O I -- --
VCC Positive Supply
(Power) Connect to positive power supply (2.4-3.6 V). Filter with a 1.0-F ceramic bypass capacitor and terminating resistor as close as possible to the VCC pin.
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
3
GND Ground
(Power) Connect to ground of the power supply. A solid ground plane is recommended for proper operation.
SD Shutdown
(Input, active high) This input is used to place the IC into a shutdown mode. TxD needs to be driven low to achieve low shutdown current.
RxD Receive Data
(Output, active low) This output provides received serial data. It is a tri-state, slew rate controlled CMOS output (tri-stated during shutdown) driver capable of driving a standard CMOS or LS series TTL load. No external resistor is required.
TxD Transmit Data
(Input, active high) This CMOS input is used to transmit serial data and has an internal pull-down resistor that is enabled only during shutdown.
LEDA LED Driver
(Power) This output is internally connected to the LED anode and contains an internal current source. The voltage range on this pad is 2.1-4.2 volts.
TAB Shield Connection
The shield tab must be soldered to ground for proper operation.
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
4
Application Block Diagrams
Figure 3 shows the application block diagrams for the ZHX1203 transceiver.
Figure 3. ZHX1203 Application Block Diagrams
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
5
Electrical and Timing Specifications
Table 2 through Table 6 list the electrical and timing specifications.
Table 2. Absolute Maximum Ratings Parameter Supply voltage Supply voltage Input voltage Symbol VCC VLED VIN TST TSOL Min -0.3 -0.3 GND-0.3 GND-0.3 -40 Max 3.6 4.4 VCC+0.3 VCC+0.3 100 240 400 Unit V V V V TxD, SD RxD Comment VCC, GND
Output (Ext.) voltage VOUT Storage temperature Solder temperature ESD
C C
V See page 9.
Table 3. Recommended Operating Conditions Parameter Supply voltage Supply voltage, LEDA Ambient operating temperature Symbol VCC VLED TOP Min 2.4 2.1 -30 Max 3.6 4.2 85 Unit V V
C
Table 4. Receiver Electrical Characteristics Parameter High-level output voltage Low-level output voltage RxD rise/fall time RxD pulse width Symbol Condition VOH VOL Tr, Tf tPWA IOH=-100 A IOL=100 A Cload=25 pF SIR<115.2 Kbps 1 Min VCC-0.4 0.4 100 5 Typical Max Unit V V ns Remarks RxD RxD 10% and 90%
s
s; rise/fall
Input pulse=1.6
time<600 ns tPWA RxD pulse width, alternate 3/16th of pulse duration. See IrDA Physical Layer specs. 9.6s
s (3/16*(1/9600))
Input pulse=19.53
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
6
Table 4. Receiver Electrical Characteristics (Continued) Parameter Startup time Latency Minimum input irradiance Maximum input irradiance Logic low input irradiance Peak wavelength Symbol Condition TSTU TRRT Eemin Eemax EeL VCC=3.3 V VCC=3.3 V VCC=3.3 V 870 Min Typical 300 25
50
Max
Unit
Remarks
s s W/cm2 h, v<(+15)
mW/cm2 h, v<(+15)
9 500 0.3
W/cm2
nm
Unless otherwise noted: VCC=3.3 V, GND=0 V, TA=25 C
Table 5. Transmitter Electrical Characteristics Parameter High-level input voltage Low-level input voltage Transmitter current Startup time LED protection timeout Trans. radiant intensity Peak wavelength Input leakage TxD pin Optical pulse width Optical rise time IE 3.6 870 VIN=0 V, VCC 9.6-115.2 kb/s 9.6-115.2 kb/s -1 1.39 100 1 30 600 Symbol Condition VIH VIL ILED TSTU 40 20 130 270 Min 0.75VCC 0.4 65 Typical Max Unit V V mA Remarks TxD TxD LEDA pin
s s
Protects LED when TxD is left high
72
mW/sr nm
h, v<(+15)
IIL tOW tOR
A s s
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
7
Table 5. Transmitter Electrical Characteristics (Continued) Parameter Optical fall time TxD pulldown resistor Symbol Condition tOF TxDRP 9.6-115.2 kb/s SD=VCC 300K Min Typical 100 Max 660 Unit Remarks
s
Unless otherwise noted: VCC=3.3 V, GND=0 V, TA=25 C
Table 6. Transceiver Electrical Characteristics Parameter High-level input voltage Low-level input voltage Receive current Shutdown current Power shutdown time Symbol Condition VIH VIL ICC ISTB TSD VIN=0 V, VCC -1 9.6 100 0.1 Min 0.75VCC 0.4 125 1.0 200 1 Typical Max Unit V V Remarks SD SD Idle SD=VCC, TxD=0 V
A A s A
Input leakage SD pin IIL Transceiver data rate
115.2 kb/s
Unless otherwise noted: VCC=3.3 V, GND=0 V, TA=25 C
Note: To minimize power dissipation, the part has been designed for optimal operation in 1.6 s mode. If the part is used in the 3/16th pulse duration mode, some devices might exhibit a phantom RxD pulse at 9.6 Kbits/s. Caution: This component is susceptible to damage from electrostatic discharge (ESD). To prevent damage and/or degradation that might be induced by ESD, use normal static precautions in handling and assembly of this component.
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
8
ZHX1203 Tape and Reel Specifications
Figure 4 shows the ZHX1203 reel specifications, and Figure 5 shows the ZHX1203 tape specifications.
-
-
-
-
Figure 4. ZHX1203 Reel Specifications
Figure 5. ZHX1203 Tape Specifications
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
-
-
ZHX1203 SIR UltraSlim Transceiver (IrMC)
9
ZHX1203 Soldering and Cleaning Recommendations
Follow these recommendations to maintain the performance of the ZHX1203 transceiver.
Reflow Soldering
* * * * *
Reflow soldering paste is recommended. Preheat: 120~150 C, 60 to 120 seconds Heating up and cooling down: 5 C/second Maximum number of reflows: 2 The temperature profile at the top surface of the ZHX1203 transceiver, shown in Figure 6, is recommended.
Figure 6. Temperature Profile for the Top Surface
Manual Soldering
* * * *
Use 63/37 or silver solder. Temperature at solder iron tip: no more than 280 C Finish soldering within 3 seconds. Handle only after the ZHX1203 has cooled off.
Cleaning
Perform cleaning under the following conditions:
* * *
PS016402-1102
Cleaning agent: alcohol Temperature and time 30 seconds below 50 C or 3 minutes below 30 C Ultrasonic cleaning: below 20 W
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
10
Moisture Prevention Guidelines
To avoid moisture absorption during transportation and storage, ZHX1203 reels are packed in aluminum envelopes (see Figure 7) that contain a desiccant with a humidity indicator. While this packaging is an impediment to moisture absorption, it is by no means absolute, and no warranty is implied. The user must store these parts in a controlled environment to prevent moisture entry. Please read the label on the aluminum bag for indicator instructions.
Figure 7. ZHX1203 Packaging
Baking
It is recommended that parts that have been stored over 12 months or unpacked over 72 hours be baked under the following guidelines. Reels 60 C for 48 hours or more Loose Parts
* * *
100 C for 4 hours or more or 125 C for 2 hours or more or 150 C for 1 hour or more
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
11
Mechanical Drawing
Figure 8 shows the mechanical specification for the ZHX1203 transceiver.
Figure 8. ZHX1203 Mechanical Drawing
Note: The ZHX1203 family of transceivers are marked as follows: ZHX1203MB = Z1203
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y
ZHX1203 SIR UltraSlim Transceiver (IrMC)
12
Ordering Information
Use the following information to order the ZHX1203 transceiver:
ZHX1203MB115THTR without AlwaysOn Listen 3500 per reel
Customer Feedback Form
If you experience any problems while operating this product, or if you note any inaccuracies while reading this product specification, please copy and complete this form, then mail or fax it to ZiLOG (see Return Information, below). We also welcome your suggestions!
Customer Information
Name Company Address City/State/Zip Country Phone Fax email
Product Information
Serial # or Board Fab #/Rev # Software Version Document Number Host Computer Description/Type
Return Information
ZiLOG System Test/Customer Support 532 Race Street San Jose, CA 95126-3432 Fax: (408) 558-8300 Email: zservice@zilog.com
Problem Description or Suggestion
Provide a complete description of the problem or your suggestion. If you are reporting a specific problem, include all steps leading up to the occurrence of the problem. Attach additional pages as necessary.
PS016402-1102
P
R
E
L
I
M
I
N
A
R
Y

▲Up To Search▲

Price & Availability of ZHX1203

	To Download ZHX1203 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .